현재 위치
[P0000JAU] AF8 DMC압착툴
() 해외배송 가능
상품명 | AF8 DMC압착툴 |
---|---|
제조사 | DMC |
원산지 | 해외 |
판매가 | 839,000원 |
적립금 |
|
상품코드 | P0000JAU |
수량 | ![]() ![]() |
SNS 상품홍보 | ![]() ![]() |
---|
수량 |
---|
이벤트
상품상세정보
The DMC AF8, qualified to MIL-DTL-22520/1* and AS22520/1*, has virtually limitless application within the specified wire range of 12 through 26 AWG. Over a thousand turret heads are available to adapt the tool frame to your specific military or proprietary contact/wire combination. The 8 impression crimp, which is standard in the AF8, assures absolute maximum tensile strength with almost every closed barrel contact. Special indent configurations and gaging are available upon request.
For proper operation, the tool must be mated with one of the following optional accessories: a military standard or non-military turret head (TH-XXX Part No. Series), a military standard or non-military positioner (TP-XXX Part No. Series), or an adjustable head (Part No. UH2-5). This is done simply by orienting the head in the keyed position, and by tightening the hex socket screws provided as part of the head.
The precision ratchet controls cycling of the tool in both directions of handle movement. This assures the same accurate crimp every time. It's like having a quality control inspector at every work station.Positive crimp depth is controlled by an 8 position selector knob conveniently located on the tool frame. The operator simply dials the desired step for the wire being used. This setting can be secured by use of a locking pin or safety wire.
A permanent dataplate is affixed to all turret heads and positioners. This plate lists specific contact part numbers, the corresponding position color code (for 3 position turret heads), and suggested selector depth settings for the wire size being used.
The AF8 is approximately 9.75" x 2.5" x 1.25" and weighs 15 oz.
Periodic gaging is recommended to insure accurate calibration. This can be done easily by setting the tool selector knob to position #4, and checking indenter closure with the M22520/3-1 Go/No-Go gage (DMC part no. G125). For a complete set of non-Mil-Spec Go/No Go gages for all selector settings, see DMC part no. 88-100.
Other than keeping the unit clean and properly stored when not in service, no operator maintenance is required. DMC offers complete factory service by knowledgeable technicians within a reasonable turnaround time. Complete instructions concerning the use, care and warranty are supplied with each tool.
The battery powered versions of this tool is the AFE8B.
The pneumatic versions of this tool is the WA27F.
The DMC1186 tool kit contains the AF8 tool frame, tool gage, and all mil-spec positioners and turret heads.
For a complete listing of AS22520 to DMC Tooling.
상품결제정보
고액결제의 경우 안전을 위해 카드사에서 확인전화를 드릴 수도 있습니다. 확인과정에서 도난 카드의 사용이나 타인 명의의 주문등 정상적인 주문이 아니라고 판단될 경우 임의로 주문을 보류 또는 취소할 수 있습니다.무통장 입금은 상품 구매 대금은 PC뱅킹, 인터넷뱅킹, 텔레뱅킹 혹은 가까운 은행에서 직접 입금하시면 됩니다.
주문시 입력한 입금자명과 실제입금자의 성명이 반드시 일치하여야 하며, 7일 이내로 입금을 하셔야 하며 입금되지 않은 주문은 자동취소 됩니다.
배송정보
- 배송 방법 : 택배
- 배송 지역 : 전국지역
- 배송 비용 : 4,000원
- 배송 기간 : 3일 ~ 7일
- 배송 안내 :
배송지역 : 전국
배송비: 물품주문 금액이 총 10만원 이상이면 무료배송 해드리며, 10만원 미만일 경우 배송료 3,500원이 부과됩니다.
(제주도 및 도서,산간지역은 추가배송비 3,500원이 추가됩니다.)
배송기간 : 전지역 배송기간은 2~3일 정도 소요됩니다.
제품 중 입고지연이 되는 제품에 한하여 배송기간이 장시간 소요될 수 있습니다.
교환 및 반품정보
1> 반품/교환/환불 |
![]() 단, 모든 반품접수는 구매 후 일주일 이내에 의사를 전달하여야 하며,주문제작및 수입의뢰품은 제외 됩니다. |
![]() (반품 기한은 배송완료 후 일주일 이내로 합니다.) |
![]() 또한 제품의 포장상태는 정상적이며, 제품과 제품박스가 원본상태여야 합니다. |
2> 반품 및 교환 불가사항 |
![]() |
![]() |
![]() |
3> 제품 A/S 관련사항 |
![]() |
![]() |
![]() |
![]() 엠에스테크에서 지원하지 않습니다. |
![]() |
![]() |